Flight controls

Aircraft flight controls allow a pilot to safely and efficiently guide his plane to the desired destination. This article describes controls used on a fixed wing aircraft of conventional design. Other fixed wing aircraft configurations may use different control surfaces but the basic principles remain. The controls for rotory wing aircraft (helicopter or autogyro) are completely different.

NB: Always get professional training before attempting to fly any kind of aircraft.

Table of contents

1 Axes of motion
2 Main Control Surfaces

2.1 Secondary effects of controls
2.2 Turning the aircraft
2.3 Alternate main control surfaces

3 Secondary control surfaces

3.4 Trimming
3.5 Other Controls

4 Related topics
5 References
6 External links

Axes of motion

An aircraft is free to rotate around three axes which are perpendicular to each other and intersect at the plane's center of gravity (CG). In order to control position and direction a pilot must be able to control rotation about each of them.

Vertical - The vertical axis passes through the plane from top to bottom. Rotation about this axis is called yaw. Yaw changes the direction the aircraft's nose is pointing, left or right. The primary control of yaw is with the rudder. Ailerons also have a secondary effect on yaw.
Longitudinal - The longitudinal axis passes through the plane from nose to tail. Rotation about this axis is called bank or roll. Bank changes the orientation of the aircraft's wings with respect to the downward force of gravity. The pilot changes bank angle by increasing the lift on one wing and decreasing it on the other. This differential lift causes bank rotation around the longitudinal axis. The ailerons are the primary control of bank. The rudder also has a secondary effect on bank.
Lateral - The lateral axis passes through the plane from wingtip to wingtip. Rotation about this axis is called pitch. Pitch changes the vertical direction the aircraft's nose is pointing. The elevators are the primary control of pitch.

It is important to note that these axes move with the aircraft, and change relative to the earth as the aircraft moves. For example, for an aircraft whose left wing is pointing straight down, its "vertical" axis is parallel with the ground, while its "lateral" axis is perpendicular to the ground.

(instructional picture goes in here)

Main Control Surfaces

The main control surfaces are attached to the airframe on hinges so they may move and deflect the air stream passing over them. This redirection of the air stream generates an unbalanced force to rotate the plane about the associated axis.

Ailerons - Ailerons are mounted on the back edge of each wing near the wingtips, and move in opposite directions. When the pilot moves the stick left, or turns the wheel counter-clockwise, the left aileron goes up and the right aileron goes down. A raised aileron reduces lift on that wing and a lowered one increases lift, so moving the stick left causes the left wing to drop and the right wing to rise. This causes the plane to bank left and begin to turn to the left. Centering the stick returns the ailerons to neutral maintaining the bank angle. The plane will continue to turn until opposite aileron motion returns the bank angle to zero to fly straight and level.
Elevators - An elevator is mounted on the back edge of the horizontal stabilizer on each side of the fin in the tail. They move up and down together. When the pilot pulls the stick backward, the elevators go up. Pushing the stick forward causes the elevators to go down. Raised elevators push down on the tail and cause the nose to pitch up. This makes the wings fly at a higher angle of attack which generates more lift and more drag. Centering the stick returns the elevators to neutral and stops the change of pitch.
Rudder - The rudder is mounted on the back edge of the fin in the tail. When the pilot pushes the left pedal, the rudder deflects left. Pushing the right pedal causes the rudder to deflect right. Deflecting the rudder right pushes the tail left and causes the nose to yaw right. Centering the rudder pedals returns the rudder to neutral and stops the yaw.

Secondary effects of controls

Ailerons: The ailerons primarily control bank. However because the air underneath a wing is denser than that above it, the lowering aileron causes more drag on its side than the rising aileron. Using ailerons causes a small amount of yaw to occur. This is more pronounced for light aircraft with long wings, such as gliders. It is usually counteracted by the pilot with the rudder.
Rudder: Using the rudder causes one wing to move forward faster than the other. Increased speed means increased lift, and hence rudder use causes a small roll effect. For this reason ailerons and rudder are generally used together on light aircraft.

Turning the aircraft

Unlike a boat, turning an aircraft is not normally carried out with the rudder. Instead the ailerons are used to bank the aircraft. The forces on the plane cause the aircraft to turn in the same direction as the bank, with a steeper bank causing a faster turn. While this is happening the nose of the aircraft has a tendency to drop, and the aircraft may also yaw, so the nose is not pointing in the direction it is flying. The elevators are used to counteract the first, and the rudder to counteract the second.

Alternate main control surfaces

Some aircraft configurations have non-standard primary controls. For example instead of elevators at the back of the stabilizers, the entire tailplane may change angle. Some aircraft have a tail in the shape of a V, and the moving parts at the back of those combine the functions of elevators and rudder. Delta wing aircraft may have "elevons" at the back of the wing, which combine the functions of elevators and ailerons.

Secondary control surfaces

Trimming

Trimming controls allow a pilot to balance the lift and drag being produced by the wings and control surfaces over a wide range of load and airspeed. This reduces the effort required to adjust or maintain a desired flight attitude.

Trim Tabs - Trim tabs are used to adjust the position of an associated main control surface. They are hinged to the back edge of the control surface and by redirecting the air stream they generate a force to hold the main control surface in the desired position.
Trimming Tail Plane - Except for very light aircraft, trim tabs on elevators are unable to provide the force and range of motion desired. To provide the appropriate trim force the entire horizontal tail plane is made adjustable in pitch. This allows the pilot to select exactly the right amount of positive or negative lift from the tail plane while reducing drag from the elevators.
Control Horn - A control horn is a section of control surface which projects ahead of the pivot point. It generates a force which tends to increase the surface's deflection thus reducing the control pressure experienced by the pilot.

In the simplest cases trimming is done by a mechanical spring which adds appropriate force to the pilot's control.

Other Controls

Spoilerss - On very high lift/low drag aircraft like sailplanes, spoilers are used to disrupt airflow over the wing and greatly reduce the amount of lift. This allows a glider pilot to lose altitude without gaining excessive airpeed.
Flaps - Flaps are mounted on the back edge of each wing near the wing roots. They are deflected down to increase the effective curvature of the wing and produce additional lift, and also reduce the stalling speed of the wing. They are used during low speed, high angle of attack flight like descent for landing.
Slats are extensions to the front of a wing, and are intended to reduce the stalling speed by altering the airflow over the wing.
Air brakes - these are used on high speed aircraft and are intended to increase the drag of an aircraft without altering the amout of lift.

References

Private Pilot Manual; Jeppesen Sanderson; ISBN 0-88487-238-6 (hardcover, 1999)

There are many additional books that deal with flying and flight training. Most will cover this topic.

External links

Although it is about models, this explains the controls well